Home

Tips

Fcs16 Floor Scraper

October 28, 2022

Maintenance Instructions; Troubleshooting - General Rip-R-Stripper Fcs16 Operator'S Manual

FCS16 RIP-R-STRIPPER FLOORING STRIPPER

FORM GOM4240301EU, VERSION 1.0

FIGURE 19

18. RIP-R-STRIPPER comes with an external front mounted weight to apply

downward force of the accessory blade. Depending on the material removed,

additional weight may be required and secured with a longer trolley

bolts. FIGURE 20 & FIGURE 21

FIGURE 20

FIGURE 21

NOTE: DO NOT exceed the maximum number of weight blocks to avoid

permanent structural damage to the RIP-R-STRIPPER. NOTE: DO NOT use the RIP-R-STRIPPER without all weight blocks properly

fixed to the main frame to prevent the weight from falling or the machine from losing

control, especially when used on floors/above ground work surfaces. NOTE: Properly dispose of all accumulated flooring materials as per

international and local environmental regulations. He is

strongly recommended that all exposed internal/external surfaces are properly

cleaned after each use plus, adjust wheel scraper clearance to minimize

accumulation on the wheels. 9 CARE INSTRUCTIONS

For routine maintenance, the following information should be followed at

minimum once a week or 40 hours of use for maximum performance and

return on investment unless otherwise stated. Inspect all fasteners, individual parts, operator controls and

safety devices for proper operation. Remove all loose material buildup, dirt and grease from

internal/external surfaces, circuit breaker body and cooling vents to prevent

safety risks, poor performance and reduced lifespan. NOTE: The electric motor is fully enclosed and fan cooled (TEFC). NOTE: Properly dispose of all accumulated flooring materials as per

international and local environmental regulations. DO NOT use thinner, benzene or

other volatile solvents that will attack rubber/plastic components when cleaned

RIP-R-STRIPPER. Inspect the RIP-R-STRIPPER ON/OFF and the red electric motor reset switch

for proper operation. Check that the operator handle grips are free of moisture, pitch, oil or grease and

are not cracked, damaged or worn. 10 TROUBLESHOOTING

NOTE: If the troubleshooting information does not correct the situation,

Service/repairs not described in this user manual must be performed by a

dedicated service center following a specific service/repair manual.

Pro Floor Stripper

Ideal for removing materials such as carpet, ceramic tile, linoleum, the Rip-R-Stripper offers high productivity, an ergonomic design and multiple removal accessories. Built with a 3/4 horsepower, 115/230 VAC, 60 Hertz electric motor, the Rip-R-Stripper delivers high productivity, yet low noise levels.

# Video | Fcs16 Floor Scraper

National 550 Floor Scraper Parts
Wolff Duro Floor Scraper Blades
Heavy Duty Floor Scraper Machine
Wolff Turbo Floor Scraper
Sinclair Floor Scraper

Fcs16 Floor Scraper Blades

General Equipment Rip-R-Stripper Fcs16 Operator'S Manual

USER MANUAL

Includes safety, service and spare parts information

Model FCS16

RIP-R-STRIPPER

Flooring stripper

Form: GOM4240301

Variant 3.2

Do not throw away this manual. When ordering spare parts, please provide the

following information: model number, serial number and part

Number. Our customer service

the fax number is 877.344.4375 (DIGGER 5), +507.451.5511.

Fcs16 Floor Scraper Manual

Floor Scraper Is Ergonomically Designed.

Scrapers

Summary of press release:

Model FCS16 Rip-R-Stripper(TM), equipped with a ¾ hp, 115/230 Vac, 60 Hz electric motor, removes carpets, ceramic tiles, linoleum and sealants. Original press release:

General Equipment Introduces the Rip-R-Stripper(TM) Flooring Scraper

OWATONNA, Minn. - General Equipment Company introduces the FCS16 Rip-R-Stripper(TM), an electric floor scraper. Ideal for removing materials such as carpet, ceramic tile, linoleum and sealants, the Rip-R-Stripper offers high productivity, an ergonomic design and multiple removal accessories. For added safety and productivity, the Back-Saver(TM) blade control system allows infinite adjustment of the blade angle during use. Options include 6-inch, 10-inch, and 16-inch straight blades (beveled edges) for removing carpet, linoleum, and ceramic tile; 6 and 10 inch angled blades (beveled edges) for removing putty; 8-inch and 12-inch straight blades (bevel edge up) for removing materials from concrete surfaces; 8-inch and 12-inch straight blades (bevel edge down) for removing material from wood surfaces; and a ripper tooth attachment for removing ceramic tile and hardwood floors.

Fcs16 Floor Scraper Parts

General Equipment Strippers

LIMITED PRODUCT WARRANTY

GENERAL EQUIPMENT COMPANY offers the following limited warranty to the original purchaser of each new and unused light construction equipment product:

GENERAL EQUIPMENT COMPANY MAKES NO WARRANTY THAT THE LIGHTWEIGHT CONSTRUCTION PRODUCTS SOLD HEREUNDER WILL BE COMMERCIAL OR THAT SUCH PRODUCTS WILL BE SUITED FOR A PARTICULAR PURPOSE AND THERE ARE NO EXPRESS OR IMPLIED WARRANTIES OTHER THAN ITS STANDARD LIMITED WARRANTY. WHAT THE LIMITED WARRANTY COVER

GENERAL EQUIPMENT COMPANY warrants each new and unused light construction equipment product and/or accessory sold by it: A) to be free from defects in materials and workmanship under normal use/service for a period of two (2) years from the date of purchase: B) to warrant labor charges associated with defects in materials and workmanship for a period of one (1) year from the date of 'purchase. Obligation under this warranty is limited to then current fixed labor rates and replacement and/or repair at its factory site in Owatonna, Minnesota, or at an authorized dealer designated by it. , of the part(s) which will appear upon inspection to have been defective in material or workmanship at the time of sale, provided that the part(s) declared defective are returned to the point of inspection, transportation charges prepaid. WHAT THE LIMITED WARRANTY DOES NOT COVER

This warranty does not cover depreciation or damage caused by: normal wear and tear, accident, improper protection in storage, misuse, modifications, alteration, environment, improper maintenance, lack of maintenance or incidental costs incurred by the original purchaser while the light construction equipment product is being examined and/or repaired under warranty. In addition to the above limitations and/or exclusions, the following basic components of the product are not covered by the limited warranty:

1) Parts and/or components subject to wear and tear under normal use, but not specifically limited to the following:

a) High impact/wear related components including but not limited to: V-belts, flails, flail rods and flail drums. 3) Engines, motors, controls, and other accessories sold with, attached to, or used with a light construction equipment product sold by GENERAL EQUIPMENT COMPANY and warranted separately by the original equipment manufacturer (OEM) under its program respective warranty.